Sauna stones: which size, how many and how to stack them
Sauna stones are part of the heater, and the heater’s maker decides which ones are allowed, how big they are and how they go in. For the Harvia heaters on our cabins that means up to 80 kg of 5–10 cm stones, a dense layer against the grid and a loose middle. Follow the heater’s instructions to choose stones and stack them, and check their condition to see when they need replacing.
- The maker decides. Harvia allows peridotite, olivine diabase, olivine and vulcanite, 5–10 cm across, split or rounded.
- Four boxes for a full load. The Harvia Cilindro PC70 and PC90 each take up to 80 kg, which is four 20 kg boxes.
- Once a year, at least. Restack, clear the fragments and replace crumbling stones; check again two months after the first stacking.
Which stones can go in a sauna heater?
The ones your heater’s maker allows. For the Harvia Cilindro that means peridotite, olivine diabase, olivine or vulcanite, split or rounded, 5–10 cm across.
Harvia’s manual for the Cilindro range is specific. It names four rock types, asks for stones of 5–10 cm in diameter, and allows split stones, rounded stones or a mix. Where the heating elements touch the stones, rounded stones belong only in the outer layers, away from the elements.
Ceramic and decorative stones are a different matter. Harvia allows them only if the heater maker has approved them, used as that maker instructs, and decorative stones only on the top layer, placed loosely so air can move. The warranty does not cover damage caused by decorative stones or by stones the manufacturer does not recommend.
Harvia gives these details because the stone pile affects both safety and how well the heater heats the room. Looking after the stone space as the manual sets out is the owner’s job, and the warranty depends on it.
Our 20 kg boxes are olivine diabase, sized 5–10 cm, which is what the Harvia heaters on The Cabin Three and our other electric cabins ask for. Keep one box label with the heater’s manual, so you know what went in when you restack or buy more. For wood-fired outdoor saunas, check the stove’s own stone requirements before choosing a model.
How many kilograms of stones do you need?
Enough to cover the elements the way the manual shows. For the Harvia PC70 and PC90 the maximum is 80 kg, so plan on four 20 kg boxes.
| Heater | Stone space, maximum | Stone size | 20 kg boxes for a full load |
|---|---|---|---|
| Harvia Cilindro PC70, 6.8 kW | 80 kg | 5–10 cm | 4 |
| Harvia Cilindro PC90, 9.0 kW | 80 kg | 5–10 cm | 4 |
Eighty kilograms is the maximum, and coverage decides how much you actually load: the heating elements have to be hidden completely, without a high pile on top. Stone shapes vary, so a full load from four boxes rarely sits exactly level with the top. Leave spare stones out rather than forcing them into gaps or heaping them up.
Have all four boxes on site before the first heat. A heater with too few stones leaves elements exposed, and Harvia warns that a bare element can endanger combustible materials even outside the safety distances. The figures in the table belong to these two heaters; other Harvia models and wood stoves have their own.
What do you do before the stones go in?
Make sure the heater is off and cold, rinse the dust off the stones, and set aside any that are cracked or crumbling.
New stones carry dust from the quarry and the box. Harvia asks for it to be washed off before the stones go into the heater, and our stones page says the same: rinse before first use. A garden hose over a crate, or a few changes of water in a bucket, does it.
Look at each stone as you rinse it and put aside any that are cracked, flaky or much smaller than the rest. If the box mixes split and rounded stones, sort them: Harvia keeps rounded stones to the outer layers, away from the elements. Lay the stones out beside the heater so you can pick them one at a time and see the elements as the pile grows.
Work only with the heater switched off at its supply and completely cold. Harvia’s warnings are blunt about a hot heater: the stones and the outer surface can burn skin. If you spot any damage to the heater while it is empty, report it before loading, as the stones will hide it.
How do you stack sauna stones properly?
A dense layer against the steel grid, a loose middle, no stone wedged between the elements or resting its weight on them, every element covered and no high pile on top.
Harvia’s method for the Cilindro comes down to a few rules. The dense outer layer stops direct heat radiating onto the materials round the heater, and the loose middle lets air rise through the heater so the room and the stones heat properly.
- Place every stone by hand. Harvia asks you never to drop them into the heater.
- Build a dense layer against the steel grid all the way round, taking extra care at the corners where the elements sit close to the grid.
- Fill the middle loosely, so air can flow up through the stone pile.
- Let the stones support each other. None should rest its weight on an element, and none should be wedged between elements.
- Keep the elements standing straight, supported by the stones around them.
- Carry on until no element shows behind the stones, then stop without making a tall pile on top.
If a stone will only go in by pressing against an element, try another position or another stone: the right size does not make every stone fit every gap. Before the first heat, walk round the heater and look at the pile from each side, corners included. Nothing else goes into the stone space or close to the heater if it could change how much air flows through it, or where, so keep ornaments and fittings off the stones.
What happens the first time you heat the stones?
The new heater and stones give off a smell, which clears once the room has been aired well. After that, water goes on 0.2 litres at a time.
Harvia warns that both the heater and the stones smell on the first heating, and the answer is to air the sauna well while it passes. Plan the first heat as a run on its own, with the room well aired, rather than as the first session. A smell later on, or anything else unusual, is a different matter: switch off and ask for advice rather than heating it again to see.
Once the room is up to temperature, water on the stones raises the humidity. The ladle holds at most 0.2 litres; more than that only partly evaporates and can splash off as boiling water. Never throw water while someone is close to the heater. Use clean household water, never pool water or seawater, as our guide to water in a garden sauna explains.
How often should you restack or replace sauna stones?
At least once a year, more often if the sauna is used a lot. Check again about two months after the first stacking, when the stones settle fastest.
Heat cycles break stones down. Harvia’s instruction is to rearrange them at least once a year, or more often with frequent use, and at the same time to clear the fragments from the bottom of the heater and replace crumbling stones with new ones. The stones settle most in the first two months, so that is the moment for the first check: look for elements showing through. If one shows at any point, restack then rather than waiting for the yearly date.
Other signs point the same way. Pieces of stone under the heater, a pile that has sunk, or a room that heats more slowly than it used to can all mean the stones need attention. Harvia lists stones piled too tightly, or settled over time, among the causes of slow heating; our warm-up guide covers the other causes.
A yearly restack does not mean a new set of stones. Sound stones go back in; the job is to clear the fragments, replace what has crumbled and rebuild the dense outside and loose middle as before.
Restacking in six steps
Do it with the heater off at its supply and completely cold. Your ticks stay on this device.
The care routine for the rest of the cabin is in our maintenance guide.
Is it different for a wood-burning stove?
The idea is the same, a stable pile that lets air through, but the rules come from the stove’s maker. Follow its manual for stone size, quantity and loading.
A wood stove holds its stones in a guard or cage, and its own manual sets the size, the quantity and how they are loaded. Read it before the first fire, as you would the heater manual on an electric cabin, and never carry the figures from a Harvia electric heater across to a stove. The wood-fired Cabin Three page lists its stove and the stones offered with it.
Quick answers about sauna stones
Do not use garden or beach stones in a Harvia heater: only the rock types and sizes named by Harvia meet its instructions and warranty terms.
Use ceramic stones only with the heater maker’s approval and only as it instructs. Harvia’s warranty excludes damage from decorative stones and from any stone it does not recommend.
Harvia’s instructions say not to form a high pile of stones on top of the heater. Steam comes from water on hot stones, a ladle at a time.
When they crack, crumble or leave fragments under the heater. Harvia asks for crumbling stones to be replaced each time you restack, which is at least once a year.
Four boxes for a full load
Our 20 kg boxes of olivine diabase, 5–10 cm, sit alongside the heater on The Cabin Three page. An expert can tell you how many your cabin needs.
What we checked for this guide
Every manufacturer figure and rule above links to its source. Checked 19 October 2026; your own equipment manual comes first where it differs.
- 01HarviaCilindro installation and user manual
- 02HarviaCilindro PC70 product page
- 03HarviaCilindro PC90 product page
Related guides
Written by the Waldenhaus team. We sell outdoor saunas and greenhouses and write these guides from manufacturer manuals, official guidance and our own product pages. Where your equipment manual says something different, follow the manual.


