Sauna wood: which timber goes on the walls, the benches and the outside
A sauna is a timber room exposed to repeated cycles of high heat, moisture and drying, week after week. The wood does three different jobs: the walls hold the heat, the benches touch your skin, and the outside faces the weather. Match sauna wood to its job. Learn which knots and cracks are normal in solid wood, and how its colour changes.
- Walls and ceiling. A low-mass timber panel, 12–16 mm thick, over insulation and a foil vapour barrier, or solid timber walls in a cabin.
- Benches that stay comfortable. Porous, low-density woods do not heat up too much; keep knots off the seat.
- Treat the outside only. Protect it against the weather and leave the inside untreated. Our alder benches need no treatment.
What wood is used in a sauna?
Sauna walls can use spruce or pine panelling, while alder and aspen are common choices for benches. Outdoor timber needs protection from the weather. Choose wood for sauna use by the part it serves: wall linings face heat and steam, and bench timber must stay comfortable against skin.
The common sauna woods differ most visibly in colour, from very dark to very light, and some show their knots more than others, as the guide to choosing sauna benches shows. For moisture handling, spruce leads the list. After pine come alder, aspen, then heat-treated alder. For an outdoor sauna, spruce is also the best at withstanding low temperatures, because its resin protects it from moisture.
| Part or choice | Common woods | Why these woods, and what to check |
|---|---|---|
| Walls and ceiling in an insulated room | Spruce, pine, aspen, alder or cedar, in the KIP manual | Low-mass panel boards 12–16 mm thick, with an air gap behind; kiln-dried, clear tongue-and-groove boards with no more than 11% moisture |
| Benches and backrests | Spruce, pine, alder, aspen and heat-treated alder, in that order for handling moisture | Porous, low-density wood does not heat up too much; keep knots off the seat. Our cabins and barrels have alder benches |
| Outdoor sauna timber | Spruce in Harvia’s comparison | Resin helps protect it from moisture in low temperatures; this is general timber guidance, not a statement of our wall species |
| Sourcing | Spruce, alder, aspen, heat-treated alder, heat-treated pine | Ask for timber that is not endangered, grown sustainably and certified |
Choose sustainably grown woods that are not endangered, from a supplier who can show certification. Ask the seller for the species and grade, and find out where the timber comes from.
What wood is used for sauna walls?
In a room built inside a house or a shed, thin softwood panels over insulation and a foil vapour barrier. In a wooden sauna cabin or barrel, solid timber boards form the wall itself.
A built-in room is layered: insulation 50–100 mm thick, foil with its glossy side towards the sauna, an air gap of about 10 mm, then low-mass panel boards 12–16 mm thick. The boards are kiln-dried, clear tongue-and-groove softwood such as spruce, pine, aspen, alder or cedar, with no more than 11% moisture, as the KIP heater manual specifies. Our guide to turning a shed into a sauna goes through that build.
An outdoor wooden sauna works differently: solid timber boards form the walls, while the roof boards sit beneath the external weather covering. Our cabins are built this way, from solid timber boards, cut to size and coded to the manual, and they arrive untreated. The same is true of a wood barrel sauna, where staves held by bands form the curve. In both, the timber moves with the seasons, so the build includes a way to keep it tight: on our Cabin range, steel straps you tighten in a dry summer and ease a little in autumn.
Which wood is best for sauna benches?
A porous, low-density wood that stays comfortable to sit on, with few knots on the seat and screws fixed from below. Harvia lists alder, aspen or heat-treated woods among the usual choices. Our cabins and barrels use alder benches, which need no treatment.
Sauna bench wood touches bare skin throughout a session. Porous woods of low density don’t heat up too much and stay comfortable to sit or lean on. Two building rules follow: keep knots off the seat, because they can become very hot, and fasten the boards from below, so no screw head on the seat can burn. We use alder for the benches in The Cabin Four. Our sauna benches guide covers their heights and depths.
Our alder sauna bench timber needs no treatment. Use bench towels during bathing, let the benches dry afterwards and wash them with a soft brush. If the surface darkens with use, sand it lightly along the grain.
Is cedar or thermowood good for a sauna?
Both are sold for saunas. Heat-treated wood, often called thermowood, is darker and less prone to warping, but Harvia notes it is slightly more fragile and more porous, so it takes up moisture more easily. For a cedar sauna, ask for the species and grade. Check how the timber is fixed too.
Heat treatment darkens the wood and reduces warping over time. But heat-treated wood is slightly more fragile and more porous than regular wood, so it takes up moisture more easily. With a thermowood sauna, steadier boards come with more care: towels on the benches and a dry room after every session.
You can choose a cedar sauna: the panelling list includes cedar alongside spruce and pine, as well as aspen and alder. The bench comparison gives no moisture ranking for cedar. Judge cedar wood for sauna use as you would any other timber: ask for the species and grade. Check whether the boards are solid or a thin facing, and how the benches are fixed. A cheap timber with many knots on the seat will be uncomfortable whatever its name.
What is normal in solid sauna wood?
Knots, a little resin, fine cracks and darkening with use are part of solid timber. Loose knots on a seat, splits that open the wall to daylight, and boards that do not match the drawing are worth raising with the seller.
Solid wood keeps moving after it is built, and it is perfectly normal for the wooden surfaces of a sauna to blacken in time, faster with sunlight, heat from the heater, protective coatings and fine particles from the stones. Knots remain visible, more so in some woods than others. Avoid them on the bench. If panels near the heater darken quickly, check the safety distances and the stones: stones packed too tightly can block the air and overheat what is near them.
A new heater and its stones smell when first heated. Ventilation clears that smell. A hot heater can also bring out smells already in the air, such as paint, glue or oil, even though these do not come from the sauna.
If a split opens the wall or a board does not match the drawing, send the seller a photograph and your order number. For our cabins, read the warranty terms for cover and how to request a replacement part. Our maintenance guide explains how to tell a dark patch from mould.
Should you treat the wood inside a sauna?
For our cabins and barrels, leave the interior timber untreated. The alder benches need no treatment. More generally, only use an interior wood treatment if the sauna or treatment manufacturer specifically approves it for hot-room use; lacquer should not be used.
Coatings that suit a garden shed do not suit a hot room: protective agents on the walls have poor heat resistance and darken the timber faster, and lacquer is ruled out on interior surfaces. Our product pages put it in practical terms: treat the outside, leave the inside untreated. At least every six months, use a scrubbing brush and sauna detergent to clean the floor as well as the benches and walls. Dry the room after every session.
How do you protect a wooden sauna outside?
With an exterior preservative or stain, on the outside only. Apply the first coat before the first session. Make sure the exterior has protection before its first winter, then reapply as the chosen product specifies. Keep the roof sealed and the base draining freely.
An outdoor wood sauna needs the same care as other garden timber, with one difference: none of the coating should reach the inside. Our Cabin pages list any exterior preservative or stain, “outside only”, among the costs on top of the cabin: the first coat goes on before the first session, and the exterior should be protected before its first winter. Keep water away from the bottom boards: a firm base that drains freely matters as much as the coating, and our guide to outdoor sauna bases covers it.
What should you ask about sauna wood before you buy?
The species and grade of each part, whether the walls are solid boards or panels, how many knots there are on the seats, whether the inside is untreated, and what the outside needs from you.
If you are buying sauna wood for sale by the board to build your own, the same questions apply, and low-priced sauna timber can cost more in the end if the bench boards are full of knots. If you are buying a cabin, the drawing and the manual should show every part. For what a low price can leave out, see our guide to cheap and expensive outdoor saunas. Our product pages describe our cabins as solid timber, untreated inside, with alder benches in The Cabin Four, and the manual for each cabin is on its page.
Wood for the sauna stove
Choose dry, seasoned logs that fit the stove’s firebox. For the ETNA 12 supplied with our wood-fired versions, logs can be up to 400 mm long. Keep the fuel dry in storage, and check the exact stove instructions before buying a load.
In England, wood fuel sold for domestic heating in volumes below 2 m³ must be certified Ready to Burn, which confirms a moisture content of 20% or less. Check the label when ordering, as GOV.UK’s wood-fuel guidance explains. Ready to Burn concerns the fuel; check with your council whether the stove can be used at your address. Our wood-fired garden sauna guide covers the stove and flue checks before you choose logs or a cabin.
Quick answers about sauna wood
For handling moisture, spruce comes first and pine second. The remaining order runs alder, aspen, then heat-treated alder. For benches, choose a porous, low-density wood with few knots on the seat.
Cedar appears on the list of softwoods for sauna panelling. The other choices include spruce and pine, as well as aspen and alder. Ask for kiln-dried, clear boards with no more than 11% moisture, and check the benches as you would for any wood.
Yes, pine appears among the softwoods listed for panelling. It ranks second to spruce for handling moisture.
For our cabins, leave the walls, ceiling and floor untreated. The alder benches need no treatment. Elsewhere, only use a treatment that the sauna or treatment maker approves for hot-room use, and never lacquer.
Sauna wood normally darkens over time. Sunlight and heat speed it up, as do coatings and stone dust. If panels near the heater darken quickly, check the safety distances and the stones.
Fine cracks are part of solid timber. If a crack opens the wall or loosens a board, send photos to the seller for a warranty assessment.
Ask the seller which timber they use for the walls, benches or roof: each may use a different wood. Ours are solid timber, untreated inside, with alder benches in The Cabin Four.
See The Cabin Three
The product page shows the boards, the benches and the manual before you order, with the full price. An expert can talk you through the timber.
What we checked for this guide
Wood properties and bench care come from Harvia’s bench guide and heater manuals; what our cabins are made of from our product pages, November 2026. Checked 9 November 2026.
- 01HarviaChoosing sauna benches
- 02HarviaKIP heater installation and owner’s manual
- 03HarviaCilindro installation and user manual
- 04HarviaMaintaining your sauna
- 05GOV.UKWood-fuel guidance
Related guides
Written by the Waldenhaus team. We sell outdoor saunas and greenhouses and write these guides from manufacturer manuals, official guidance and our own product pages. Where your equipment manual says something different, follow the manual.


