Turning a shed into a sauna, or buying a kit: what a DIY sauna really needs
A sauna holds air at 70–90 °C, and most of the work of holding it safely is hidden in the walls. Insulation, a foil vapour barrier, a lining of thin untreated boards, two vents and a heater fixed at its safety distances turn four walls into a hot room. Compare this list for building a sauna with your garden shed to judge whether a conversion makes sense or you should start from a kit.
- The walls do the work. A sauna wall needs 50–100 mm of insulation, a foil moisture barrier with taped seams and a 12–16 mm timber lining.
- The heater sets the rules. Room volume, the glass in the walls, the minimum ceiling height and the safety distances all come from its manual.
- The paperwork is the same either way. A heater circuit falls under Part P, a wood stove under Part J, and the outbuilding rules apply to any garden sauna.
What turns a room into a sauna?
An insulated shell, a moisture barrier on the warm side, a lining of thin untreated boards, ventilation, a heat-resistant floor and a heater sized and fixed to its manual. A Finnish sauna usually runs at 70–90 °C, and every layer is there to hold that heat safely.
Harvia’s installation manual for its Cilindro heaters draws the wall of a sauna in section. From the outside in, it runs like this:
| Layer or rule | Requirement |
|---|---|
| Insulation | mineral wool, 50–100 mm, “so that the heater output can be kept moderately low” |
| Moisture protection | foil such as aluminium paper, glossy side towards the sauna, seams taped with aluminium tape |
| Air gap | about 10 mm between the foil and the boards (recommended) |
| Lining | low-mass panel boards, 12–16 mm thick |
| Ceiling | about 3 mm gap between the wall and ceiling boards |
| Height | usually 2,100–2,300 mm; at least 1,900 mm for the PC70 and PC90 |
| Upper bench to ceiling | no more than 1,200 mm |
| Floor | ceramic coverings with dark grout, because stone particles and sauna water can stain sensitive floors |
Ask the fire authorities which parts of a firewall you may insulate. Never insulate a flue in use. The drawing also warns that light protective covers fixed straight onto the wall or ceiling can pose a fire risk. Keep the lining bare inside: protective agents on sauna walls cope poorly with heat. Our own assembly manual puts every treatment on the outside of the cabin, leaving untreated wood in the hot room. Compare our sauna cabins for the garden if you are weighing a separate cabin against converting the shed. For a tight plot, compare compact garden saunas against the space your shed conversion would leave.
Can a garden shed become a sauna?
It can, if it takes every layer in the table and still keeps its headroom. The frame also has to carry the benches and the heater. Judge the shed from the inside, because that is where most of the work goes.
Go through the shed with the table in hand. Is there room inside the frame for 50–100 mm of insulation, with the foil, a 10 mm gap and a lining on top? Will the finished ceiling still clear 1,900 mm, and ideally 2,100 mm or more? Can the wall behind the heater take its fixings and the floor take water and hot fragments of stone? The floor covering where the heater stands has to be heat-resistant.
Then look at what the shed was built for. If its boards were treated with a preservative, they belong outside the hot room, with new untreated boards forming the lining. Windows count against you twice: they let heat out, and by Harvia’s rule each square metre of glass adds 1.2 m³ to the room volume the heater has to serve.
Can your shed take it?
Tick what your shed can take. Your ticks stay on this device.
What does the heater ask of a DIY sauna?
A room volume inside its rated range once glass is counted, its full safety distances, a ceiling at least as high as its minimum and, for an electric heater, its own circuit fitted by a qualified electrician.
Harvia is unusually blunt about the distances: installing the heater according to the values in its manual is “absolutely necessary”, and neglecting them causes a risk of fire. A sauna room takes only one electric heater, and it may only be connected by an authorised, professional electrician. The junction box has to be splash-proof and no higher than 500 mm above the floor, and the cable has to be rubber, type H07RN-F.
A socket already in the shed is no supply for a heater: the heater needs its own circuit, designed and connected by the electrician.
Sizing follows the room. Our guide to sauna heater size shows how to measure the volume, how much each square metre of glass adds and which kW range covers the result.
Which rules apply to a home-made sauna?
The same as for a kit. A new circuit for an electric heater is notifiable under Part P in England, a wood stove and flue are building work under Part J, and the outbuilding rules decide whether the building itself needs permission.
A new circuit is notifiable work under Part P of the Building Regulations in England, and the IET’s guide to Part P counts a room containing a sauna heater as a special location, where changes to existing circuits are notifiable too. A registered electrician can certify it; otherwise building control is told before the work starts. Our guide to electrical requirements for an outdoor sauna covers the supply and the questions to ask.
A wood-burning stove brings Part J and, in a smoke control area, the rule that wood may only be burned in a Defra-exempt appliance, which our article on the wood-fired garden sauna explains. Whether the building needs planning permission depends on its size and position. In England, Planning Portal’s outbuildings guidance sets limits such as a maximum height of 2.5 m for a building within 2 m of a boundary, and our planning permission guide sets out the rest.
When does a sauna kit make more sense?
When the shed would need most of the list rebuilt anyway, or when you want a design whose parts, drawings and manual already fit together. A conversion suits someone with an insulated building and the skills to line it.
Decide how much of the design you can work out yourself. Building your own sauna in a shed means working out the insulation, the foil, the vents, the bench heights and the heater position yourself, against the manuals. In a kit those answers come in the crate.
| Shed conversion | Sauna kit | |
|---|---|---|
| Design of walls, benches, vents | yours, from the heater manual | done, in the drawings |
| Parts | bought one by one | in one crate, counted against a parts list |
| Instructions | the heater manual and your own plan | an illustrated assembly manual |
| Base | whatever the shed stands on | a firm, level base of the cabin’s footprint |
| Electrician or stove installer | needed | needed |
| Planning and building rules | apply | apply |
The Cabin Three shows what a kit puts in the crate: a 1.85 × 2.20 m cabin in solid timber, an 8 mm toughened glass door, the benches and backrest, a vent valve and a floor drain, all in one flat pack. The product page says two people build it in a weekend, typically, and the supplier estimates 8 to 12 working hours for two people. The base, the assembly, the exterior treatment and the electrician’s work are yours, as they would be in a conversion. Our article on building a garden sauna kit walks through that build.
Quick answers about DIY saunas
Keep the inside bare. Our assembly manual treats only the outside of the cabin, protective agents on sauna walls tolerate heat poorly, and Harvia’s care guidance rules out lacquer on the inside surfaces.
The heater may only be connected by an authorised, professional electrician, and the new circuit is notifiable under Part P in England.
In a sauna shed, the electrics and any stove do, as notifiable work. Whether the building itself needs planning permission depends on its size and position, set out in our planning guide.
The assembly manuals for our cabins sit on each product page, so you can compare the steps with your own plan before you buy.
How do you decide this weekend?
Measure the shed against the table, count the windows, and read a kit manual side by side with your list.
Take the tape measure out to the shed with this page open: inside height, room for insulation, wall for the heater, square metres of glass. Then download the manual for The Cabin Three and read its build order next to your list. One of the two will look shorter.
See The Cabin Three
The product page has the assembly manual, the parts that come in the crate and everything the cabin needs from your garden. An expert can answer your questions before you order.
What we checked for this guide
The build-up of a sauna room comes from Harvia’s installation manual; the rules from the IET, GOV.UK and Planning Portal; the kit details from The Cabin Three page and assembly manual. Checked 4 November 2026.
- 01HarviaCilindro installation and user manual
- 02IETGuide to Part P
- 03Planning PortalOutbuildings: planning permission
- 04HarviaMaintaining your sauna
Related guides
Written by the Waldenhaus team. We sell outdoor saunas and greenhouses and write these guides from manufacturer manuals, official guidance and our own product pages. Where your equipment manual says something different, follow the manual.


